Line

Beverage co-pack

PET and HDPE beverage co-pack lines sealing 28 to 38 mm necks before cold-chain packing.

Primary sealer: Seal Induction Pro

PET beverage co-pack line approaching an induction sealing cell

Beverage co-pack

Beverage co-pack lines in South Africa often run PET water, juice, sports drinks, HDPE cultured drinks and short RTD batches on the same conveyor. The common neck range is 28 to 38 mm, with flat caps, sports caps and retailer tamper sleeves moving into chilled storage or ambient dispatch.

The seal depends on a clean bottle land, the right aluminium liner and cap torque that presses the liner evenly onto the neck. Wet cap tops, flavour splash, dusty closures and mixed cap bins cause most start-up trouble on beverage shifts, especially after sanitation or a fast SKU change.

Seal failures seen on beverage packs

Weak peel strength usually comes from low torque, product on the neck finish, a cap started crooked or a bottle shoulder leaning through the sealing point. Burnt liners, wrinkled marks and soft PET neck panels point to an aggressive setting for that bottle and cap combination.

Random leakers often trace back to missing foils in the cap, double liners or caps from two batches in one hopper. Sleeve faults show as split perforations, high bands, fish-mouths and trapped condensate. On beverage sleeves, the usual adjustments are sleeve cut length, tunnel steam setting, bottle spacing at the infeed and the air knife position after shrink.

BottleSealer set-up for co-pack work

For capped PET and HDPE beverage bottles, BottleSealer normally starts with the Seal Induction Pro. The sealer is set on the live conveyor after capping, with guides holding bottles upright. The setter records cap torque, bottle type, cap supplier, liner batch, power, belt speed, head height and sample results for each SKU.

Where the same line needs retailer tamper bands, the Band Shrink 240 suits peak beverage work with two lanes, each rated at 120 bpm. For audit-heavy retail or export weeks, Seal Inspect Vision reads every capped bottle for liner presence and seal presentation, then diverts suspect bottles from the flow.

From filler to packed case

A steady beverage sequence runs rinse or air clean, fill, cap application, torque check and induction sealing. Samples are cooled at the line bench, opened for peel checks and tested for leaks. Sleeved SKUs then move through band placement, steam shrink, drying, coding, labelling where used, tray loading, shrink wrapping or case packing.

Changeover discipline matters on co-pack lines because the next job may bring a new neck, closure colour, liner type and label height. Clear old caps and sleeves, confirm the foil wad, set torque, centre the bottle path, run a small pack-off and sign off the first accepted case.

Maintenance and fit notes

Shift checks stay close to the conveyor: wipe juice mist from rails, clear cap dust from sensors, check belt tracking, test the reject pocket with marked bottles and drain condensate around the steam area. Watch bottle sway at full flow, because light PET can lean through bends and reach the sealer with the cap off centre.

Fit checks start with the existing conveyor height, capper position, straight section and access for operators. BottleSealer can assess guide rails, reject pockets, sleeve feed and inspection placement around the current line. For co-pack trials, send the neck finish, cap spec, liner type, drink family and target case format through our contact form so the trial matches the next production week.

Typical customer situation

A Gauteng beverage co-packer needed one sealing and shrink area to change from 28 mm PET water before lunch to 38 mm HDPE juice after sanitation, then finish with sleeved promotional packs for retailer dispatch. The set-up used induction sealing for the capped bottles, dual-lane sleeve shrinking for the promo load and vision rejection for mixed-cap weeks. The handover pack gave setters recipes, sample checks and reject tests for each SKU group.

What our Bottle Sealing customers say

Verified Google reviews

Talk to the sealing counter

Contact form · Meadowdale Industrial, Germiston