Steam band

Band Shrink 120

Steam-assisted shrink band applicator for neck bands and tamper sleeves on mid-speed lines.

Band Shrink 120

Band Shrink 120

The Band Shrink 120 is a steam-assisted neck band and tamper sleeve machine for mid-speed bottling lines. The sleeve must arrive level around the closure, and steam then shrinks it onto the cap skirt and bottle finish. It is rated for a single lane at 120 bottles per minute, with sleeve heights from 20 to 60 mm. See the Band Shrink 120 specs for format and utility details.

This machine suits plants where a setter already controls cap height, bottle pitch and downstream drying. A Stellenbosch juice plant can use it on capped PET blends with branded tamper bands. A Durban personal-care line can run neck sleeves on shampoos and lotions. A Pretoria nutraceutical packer can use tear perforation bands on short-neck bottles where tamper evidence must look clean on shelf.

Where it sits in the packing line

After capping, the Band Shrink 120 takes over when the closure is fully seated and the bottle is tracking squarely on the conveyor. The sleeve feed must meet even bottle pitch, because touching sleeves can drag, wrinkle or shrink unevenly. After the steam zone, the bottle needs drip control and drying time before date coding, labelling, sleeving cartons or tray work.

Upstream work makes the shrink easier to tune. Caps must be level, necks must be free of product splash, and the cut sleeve has to suit neck diameter, band height and the position of the tear line. On the outfeed, watch for condensate around cap skirts and shoulders. Wet bands can mark labels, so drying air or a short run-off section is often part of the cell.

What the first shift looks like

On the first production shift, the setter brings steam up to temperature, checks condensate drain points and runs empty bottles through the tunnel to confirm tracking. The sleeve feed tray is squared, the band height is set on the neck, and the first bottles are run slowly. Increase steam in controlled adjustments until the sleeve grips the closure evenly and stays straight through the shrink zone.

Once shrink is even, the operator records steam pressure, line speed, sleeve height, bottle pitch and drying setting for that SKU. The first good case should show a straight top edge, a readable tear perforation and no sleeve lift under the cap skirt. If the band rides up, check sleeve height and bottle pitch before adding more steam.

Shrink faults seen on the floor

A skew band usually starts at placement: the sleeve enters the steam zone tilted, or the bottle is wandering between guides. A split tear line points to perforation position, over-tight lay-flat width or too much dwell. A loose lower edge usually means the sleeve has not had enough steam contact for the neck finish, the dwell is too short, or the band size needs tightening.

Condensate is part of steam work, so the drain route and drying point need daily attention. Water collecting under the hood can drip onto fresh sleeves and leave spots or soft bands. Wipe-downs, hood gasket checks and a clear drain path keep the tunnel steady. For booked maintenance and wear parts, use Band Shrink 120 service.

Choosing the matching steam model

The Band Shrink 120 fits one mid-speed sleeve lane across a mixed bottle set. Beverage peak runs that need paired sleeve lanes can move to the Band Shrink 240, with two 120 bpm lanes sharing the same steam layout. Compact co-pack cells using narrow-mouth bottles can look at the Steam Tunnel S.

Wide-mouth packs need a tunnel built around the container width and shoulder shape. Chemical, oil and gallon formats pair well with the Steam Tunnel L, where sleeve dwell and steam contact suit jerry and gallon containers. For Band Shrink 120 trials, send bottle diameter, cap height, sleeve cut height and tear-line position through our contact form.

Rate bandUp to 120 bpm
Power / utilitiesSteam + 2.2 kW
Neck / formatSleeve heights 20 to 60 mm

Specs · Service.

What our Bottle Sealing customers say

Verified Google reviews

Talk to the sealing counter

Contact form · Meadowdale Industrial, Germiston