2026-09-03

Foil wads for common SA necks

28, 33, 38, and 45 mm finishes we stock for short-run kits.

By Ms Tasneem Latief · Foil and die specialist

Foil wad discs for common SA neck finishes laid out in trays

Foil wads for common SA necks

Foil wads for 28, 33, 38 and 45 mm necks catch many plants out during short-run packing. The cap looks correct, the bottle looks familiar, and the first case passes down the line. The leak appears later because the wad sat off centre, wrinkled under the cap skirt, or covered too little of the bottle sealing face.

On local lines, the same store of closures may serve nutraceuticals, cosmetics, sauces, syrups, edible oils and household packs while bottle styles change from job to job. The cap size alone is not enough. The bottle land, cap depth, liner stack and torque decide whether the heat-seal layer sits flat. Foil & Die Kit checks start by presenting the actual bottle finish, closure and wad as one set.

Why the fault shows after packing

A cap that torques cleanly can still hide a poor wad match. The liner may shift as the thread starts, especially when side guides press the bottle shoulder or when the capper applies uneven pressure. After sealing, the fault shows as a dry crescent on the peel, product creep at one edge, or a bottle that weeps when squeezed.

Product on the land makes the same fault worse. Oil carry-over, syrup stringing, powder dust and foaming cosmetic fills reduce contact where the bond must form. Before changing sealer settings, the setter should check fill height, land cleanliness, cap pick-up and torque repeatability. The foil neck chart gives a starting point for common local finishes.

Step-by-step method on the floor

First, check the wad outside production pressure. Place the foil in the cap, close it on a clean empty bottle, open it again and look for flat, centred seating. Second, cap filled samples at normal torque. If the liner drags or skews during thread start, correct cap handling, bottle guides or torque before adding heat.

Third, run a short sealing trial. A benchtop Seal Induction Compact suits lab batches and small contract runs, while Seal Induction Pro suits moving production. Start moderately, then adjust power and belt speed until the foil bonds cleanly without neck distortion, cap marking or liner movement.

Fourth, pull samples at start-up, after a cap box change, after a bottle pallet change and after stop-start events. Record peel feel, foil appearance and the plant’s leak test result. Keep failed samples with the batch notes until release, because the damaged wad often shows whether the fault came from torque, dirt, size or heat.

What to record for repeat runs

A useful wad record is short and specific: SKU, bottle supplier, cap supplier, neck size, wad diameter, liner grade, torque value, sealer setting, belt speed, product temperature, land condition and the operator who signed off the first acceptable sample. Add one photo of a good peel and one photo of any reject pattern.

Maintenance notes belong with that record. Check that bottle guides hold the container straight without rubbing the shoulder, that cap chucks or pads are not worn on one side, and that the capper gives repeatable torque after changeover. A seal check card keeps checks consistent across shifts.

Worked example from a typical line

A Gauteng co-packer running a 38 mm nutraceutical syrup moved from a tall PET bottle to a shorter HDPE bottle while keeping the same closure colour. The first trial leaked after overnight holding. The peel showed one bonded half and one dry half, with the wad sitting slightly off centre inside the cap.

The correction was practical. The team checked liner seating in the cap, reduced torque enough to stop the wad dragging during thread start, tightened the side guides at the capper exit, then repeated the trial with fresh 38 mm wads. For the 38 mm changeover, the deciding checks were wad centring inside the closure, even land contact and a peel that showed bond right around the bottle mouth.

What our Bottle Sealing customers say

Verified Google reviews

Talk to the sealing counter

Contact form · Meadowdale Industrial, Germiston